service@ertec.com.uy Posts: 4
1/13/2017
|
Feeeblox support 2 or more different sip providers and 1 ip pbx? How configure that?
|
|
0
link
|
hmmartinez Posts: 18
4/2/2019
|
I would like to configure 2 or more different SIP providers and 2 or more PBX,... How can it be possible?
Specifically, I want an external SIP trunk to go to two different PBXs and another external SIP trunk to go to another third PBX.
Thanks in advance edited by hmmartinez on 4/2/2019
|
|
0
link
|
bloxsupport1 Posts: 232
4/5/2019
|
You can configure 2 or more sip provider and also more PBX in the SIP domain and can create different sip profiles for Trunk but Inbound call routing can be routed to only one pbx.
Thanks and Regards Blox support Team.
hmmartinez wrote:
I would like to configure 2 or more different SIP providers and 2 or more PBX,... How can it be possible?
Specifically, I want an external SIP trunk to go to two different PBXs and another external SIP trunk to go to another third PBX.
Thanks in advance edited by hmmartinez on 4/2/2019
|
|
0
link
|
hmmartinez Posts: 18
4/12/2019
|
Hi,
And is it possible that the same SBC (with a SIP Trunk) could differentiate and route the call to one or another PBX (Production or Training environment, for example), depending on the number called (DDI number)?
Thanks & Regards, edited by hmmartinez on 4/12/2019
|
|
0
link
|
bloxsupport1 Posts: 232
4/12/2019
|
currently Blox supports forwarding to single inbound URI from the Trunk, and feature to route based on DID is not supported.
|
|
0
link
|
hmmartinez Posts: 18
5/24/2019
|
bloxsupport1 wrote:
You can configure 2 or more sip provider and also more PBX in the SIP domain and can create different sip profiles for Trunk but Inbound call routing can be routed to only one pbx.
Thanks and Regards Blox support Team.
So, if I have 2 SBCs and 2 internal PBXs, would the SBCs be able to balance between the two PBXs or is the connection one-to-one (one SBC to one internal PBX)? If a PBX connection fails, does the SBC balance to the other PBX? Can I have a single external SIP Trunk configured in the SBC and that it acts as a balancer?
Thanks & regards,
|
|
0
link
|
hmmartinez Posts: 18
6/3/2019
|
hmmartinez wrote:
So, if I have 2 SBCs and 2 internal PBXs, would the SBCs be able to balance between the two PBXs or is the connection one-to-one (one SBC to one internal PBX)? If a PBX connection fails, does the SBC balance to the other PBX? Can I have a single external SIP Trunk configured in the SBC and that it acts as a balancer?
Does anyone know an answer to my question / problem?
|
|
0
link
|
hmmartinez Posts: 18
6/5/2019
|
bloxsupport1 wrote:
currently Blox supports forwarding to single inbound URI from the Trunk, and feature to route based on DID is not supported.
Instead of using DDIs to route between different SIP Trunks, could LCR (Lest Cost Routing) be used to route the call to one or another SIP Trunk? How would the LCR configuration work?
|
|
0
link
|
hmmartinez Posts: 18
6/18/2019
|
¿Any idea?
|
|
0
link
|
bloxsupport1 Posts: 232
6/19/2019
|
Its not possible to do load balance between PBX or fallback Trunk inbound calls, it is one to one mapping
LCR works on virtual trunk created/configured from PBX to SBC for outbound dial, SBC can match and reroute the call using Diversion towards PBX to pick the Real Trunk
|
|
0
link
|